1.接送料的工作臺面和切刀下部保持水平，鋼筋切斷機工作臺的長度可根據加工材料的長度確定。
2.啟動前，應檢查并確認切刀無裂紋，倒架螺栓緊固，防護罩牢靠。然后用手傳動皮帶輪，檢查齒輪咬合間隙，調整切刀間隙。
3.啟動后，應先空運轉，檢查個傳動部分及軸承運轉正常后，方可作業。
4.機械未達到正常運轉時，不得切料。切料時應使用切刀的中下部位，緊固鋼筋對準刃口迅速投入，操作者應站在固定刀片的一側用力壓住鋼筋，應防止鋼筋末端彈出傷人。嚴禁用兩手在刀片兩邊握住鋼筋俯身送料。
5.不得剪切直徑及強度超過機械銘牌規定的鋼筋和燒紅的鋼筋。一次切斷多根鋼筋時，其總截面面積應在規定范圍內。
6.剪切低合金鋼時，應更換高硬度的切片，剪切直徑應符合機械名銘牌的規定。
7.切短料時，手和切刀之間的距離應保持在150mm以上，如手握端小于400mm時，應采用套管或夾具將鋼筋短頭夾注或夾牢。
8.運轉中嚴禁用手直接清除切刀附近的斷頭和雜物。鋼筋擺動周圍和切刀周圍不得停留非操作人員。已切斷的鋼筋堆放要整齊，防止切口突出，誤踢割傷。
9.當發現機械運轉不正常，有異響或切刀歪斜時，應立即停機整修。
10.作業后應切斷電源，用鋼刷清除切刀見的雜物，進行整機清潔潤滑。

中譯英：
1 material feeding table and a cutter lower level, the length of the working platform can be processed according to the length of the material determination.
2 start before, should check and confirm the cutter without crack, inverted frame bolt fastening, protective cover firm. Then by hand driving pulley, gear meshing clearance check, adjust the cutting clearance.
3 after the start, should first check idle, a transmission part and bearing in normal operation, we can work.
4 machinery does not reach the normal operation, not cutting. When cutting materials should be used in the middle and lower part of the cutter, the fastening reinforced alignment edge quickly put, the operator should stand on the side of the fixed blade cloth reinforced, should prevent the reinforced end out to hurt people. Prohibit the use of both hands in the blade on both sides hold reinforced leaned feeding.
5 may not cutting diameter and strength more than machinery nameplate provisions and a red-hot steel reinforced. A cut a plurality of steel bars, the total cross-sectional area should be in the specified range.
6 Shear low alloy steel, replace the high hardness of the section, shear diameter shall be in accordance with the provisions of the machine name.
7 cutting short materials, hand and knife distance should be maintained at more than 150mm, such as holding end is less than 400mm, should adopt the casing or fixture to be reinforced by short head or to.
8 movement is prohibited by hand directly clear cutting knife near the breakage and sundries. Reinforced swing around and cutter may not stay around non operators. Have cut off the steel piling to prevent incision neatly, prominent, mistakenly kicked.
9 when the machine is not operating properly, abnormal sound or the cutter deflection, should immediately stop renovation.
10 operation should be cut off the power, steel brush to remove cutter saw debris, cleaning and lubricating machine.
(圖/文www.ncwanke.cn)